nplan 0.29~16.04.1 source package in Ubuntu

Changelog

nplan (0.29~16.04.1) xenial; urgency=medium

  * Backport netplan 0.29 to 16.04. (LP: #1713142)
  * debian/control: Depend on systemd (>= 229-4ubuntu20) for the PrimarySlave
    feature backported in that revision.

nplan (0.29) artful; urgency=medium

  * Fix autopkgtests in a world where /run/NetworkManager/conf.d already
    exists. nplan is enabled by default, so it might well have the directory
    already created on the filesystem.

nplan (0.28) artful; urgency=medium

  * Revert 56cd3eec which disabled IPv6 Router Advertisements by default. It
    broke default network config in LXD and was contrary to the defaults used
    by the kernel. Reopens LP: 1655440. (LP: #1717404)
  * Add "accept-ra:" key for all device types; this will default to OFF but
    allow users to disable processing Router Advertisements when required by
    their network setup. (LP: #1655440)

nplan (0.27) artful; urgency=medium

  [ Mathieu Trudel-Lapierre ]
  * Fix crash in systemd generator if called by an user on the command-line.
    (LP: #1714267)
  * coverage: fix exclusions to properly not cover our "never reached defaults"

  [ Dimitri John Ledkov ]
  * tests/integration.py: In teardown, stop systemd-networkd.socket.
  * src/networkd.c: Set UseMTU=true by default, whenever DHCP is in use.
    (LP: #1717471)
  * tests/integration.py: fix resolved detection.

nplan (0.26) artful; urgency=medium

  * Bonding:
    - Add support for specifying a primary slave. (LP: #1709135)
  * Rebind:
    - Fix brcmfmac harder. Treat any 'brcmfmac' driver as not supporting
      rebind. (LP: #1712224)
  * Autopkgtests:
    - Add allow-stderr. Systemd now bleats about a the networkd socket still
      being around and enabled when we restart the service; but we don't need
      to care since we're /restarting/ the service to load the new config.
    - Fix the autostart package to be more sensible: we don't really care if
      networkd autostarts or not, but we need to make sure that our generator
      will run at boot, so instead check the state, but only assert it once
      we've added a config file and before checking the state of our dummy
      device.
    - Do a bit more to make sure "mix" tests which stack virtual devices are
      as reliable as possible; by setting saner defaults.

nplan (0.25) artful; urgency=medium

  * tests/generate.py: add a test to validate that correct blacklist entries
    are added when creating virtual devices.
  * tests/integration.py: clean up after br0 in networkd's test_bridge_mac; as
    the remaining interface and udev configuration can confuse NetworkManager
    now that it seems to manage random devices it did not create again.
    (LP: #1699371)
  * src/nm.c: set the MTU even though we also specify it in systemd-networkd
    for consumption by udev. NetworkManager will try to set it and might
    otherwise default to the wrong value.
  * src/networkd.c: Set IPv6AcceptRA=no anytime we don't do DHCPv6 (or by the
    same config, SLAAC), and don't have static addresses set. This should fix
    the cases where unconfigured devices still get an IPv6 address.
    (LP: #1655440)
  * src/nm.c: Explicitly set IPv6 method=ignore when IPv6 is otherwise not
    configured; this follows the same logic as setting IPv6AcceptRA=no in
    networkd, with the exception that NM does not currently disable RAs. When
    it does, an unconfigured device for IPv6 will truly be left with no config.

nplan (0.24) artful; urgency=medium

  * debian/control: set Priority to important to make sure we can get into
    minimal.

 -- Mathieu Trudel-Lapierre <email address hidden>  Tue, 26 Sep 2017 14:08:21 -0400

Upload details

Uploaded by:
Mathieu Trudel-Lapierre on 2017-10-04
Uploaded to:
Xenial
Original maintainer:
Ubuntu Developers
Architectures:
any
Section:
net
Urgency:
Medium Urgency

See full publishing history Publishing

Series Pocket Published Component Section
Xenial proposed on 2017-10-06 universe net

Downloads

File Size SHA-256 Checksum
nplan_0.29~16.04.1.tar.gz 70.3 KiB 00238f84cf57a58ec6bba1a5303b14145249c8fe1735831ddd4216764327444d
nplan_0.29~16.04.1.dsc 1.7 KiB 40bf8971f88161d9ab0884d4352a84e7a6daaf2df3d06572b3c8169d7c274315

Available diffs

View changes file

Binary packages built by this source

nplan: YAML network configuration abstraction for various backends

 netplan reads YAML network configuration files which are written
 by administrators, installers, cloud image instantiations, or other OS
 deployments. During early boot it then generates backend specific
 configuration files in /run to hand off control of devices to a particular
 networking daemon.
 .
 Currently supported backends are networkd and NetworkManager.

nplan-dbgsym: debug symbols for package nplan

 netplan reads YAML network configuration files which are written
 by administrators, installers, cloud image instantiations, or other OS
 deployments. During early boot it then generates backend specific
 configuration files in /run to hand off control of devices to a particular
 networking daemon.
 .
 Currently supported backends are networkd and NetworkManager.