Comment 34 for bug 29789

i have 7.10 with kernel 2.6.22-14-rt using a wintv card. i have the same problem: the line out of the wintv card is not working. well almost cause i can hear a little bit if i really boost the sound on my amplifier (+30db).

i was hoping to use btaudio to driver the 32000 hertz to /dev/dsp2 (or so). but modprobe btaudio is not present. locate btaudio gives nothing. maybe it's my configuration.

[ 45.692860] bttv: driver version 0.9.17 loaded
[ 45.692868] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 45.692954] bttv: Bt8xx card found (0).
[ 45.692983] ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 20
[ 45.692998] bttv0: Bt878 (rev 17) at 0000:02:0a.0, irq: 20, latency: 64, mmio: 0xf8ffe000
[ 45.693015] bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb
[ 45.693019] bttv0: using: Hauppauge (bt878) [card=10,autodetected]
[ 45.693052] bttv0: gpio: en=00000000, out=00000000 in=00ffffdb [init]
[ 45.695773] bttv0: Hauppauge/Voodoo msp34xx: reset line init [5]
[ 45.753326] tveeprom 0-0050: Hauppauge model 44811, rev C323, serial# 2631909
[ 45.753332] tveeprom 0-0050: tuner model is Philips FM1236 (idx 23, type 2)
[ 45.753336] tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
[ 45.753340] tveeprom 0-0050: audio processor is None (idx 0)
[ 45.753343] tveeprom 0-0050: has radio
[ 45.753346] bttv0: Hauppauge eeprom indicates model#44811
[ 45.753349] bttv0: using tuner=2
[ 45.753354] bttv0: i2c: checking for MSP34xx @ 0x80... not found
[ 45.753946] bttv0: i2c: checking for TDA9875 @ 0xb0... not found
[ 45.754528] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 45.802424] bttv0: i2c: checking for TDA9887 @ 0x86... not found
[ 45.854762] tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
[ 45.854803] tuner 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
[ 45.854808] tuner 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
[ 45.863597] bttv0: registered device video0
[ 45.863647] bttv0: registered device vbi0
[ 45.863689] bttv0: registered device radio0
[ 45.863713] bttv0: PLL: 28636363 => 35468950 .. ok
[ 45.886293] bttv: Bt8xx card found (1).
[ 45.886319] ACPI: PCI Interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 45.886334] bttv1: Bt878 (rev 17) at 0000:02:0d.0, irq: 21, latency: 64, mmio: 0xf8ffc000
[ 45.886360] bttv1: detected: Osprey-200 [card=88], PCI subsystem ID is 0070:ff01
[ 45.886364] bttv1: using: Osprey 200/250 [card=88,autodetected]
[ 45.886394] bttv1: gpio: en=00000000, out=00000000 in=00ffffff [init]
[ 45.943203] bttv1: osprey eeprom: card=89 name=Osprey 210/220/230 serial=3081860
[ 45.943209] bttv1: using tuner=-1
[ 45.943214] bttv1: i2c: checking for TDA9887 @ 0x86... not found
[ 45.944303] bttv1: registered device video1
[ 45.944669] bttv1: registered device vbi1
[ 45.944695] bttv1: PLL: 28636363 => 35468950 .. ok

also i halsa an osprey for capturing video from composition or svideo.
[ 45.753340] tveeprom 0-0050: audio processor is None (idx 0):
not looking good?

i can see video perfectly with tvtime

xawtv fail on me:
xinerama 0: 1280x1024+0+0
xinerama 1: 1280x1024+1280+0
X Error of failed request: XF86DGANoDirectVideoMode