Ubuntu
usplash package

usplash and TTY terminals wont show up with Feisty on my Dell GX 260 Intel 82845G video chipset

Bug #105672 reported by PresuntoRJ
4
Affects Status Importance Assigned to Milestone
usplash (Ubuntu)
New
Undecided
Unassigned

Bug Description

Binary package hint: usplash

I have used previous versions on the same machine and I do use Feisty on several other hardware plataforms.

USplash wont show up anything during the boot or shutdown (halt -n) using Ubuntu 7.04 Beta fully up to date on my Dell Optiplex GX 260 (video Intel 82845G/GL)

This is my # lspci

00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 01)
00:02.0 VGA compatible controller: Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
01:0c.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)

This is my # lspci -vv

00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 01)
        Subsystem: Dell Optiplex GX260
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [e4] Vendor Specific Information

00:02.0 VGA compatible controller: Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 01) (prog-if 00 [VGA])
        Subsystem: Dell Unknown device 0126
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
        Region 1: Memory at ff680000 (32-bit, non-prefetchable) [size=512K]
        Capabilities: [d0] Power Management version 1
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI])
        Subsystem: Dell Optiplex GX260
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at ff80 [size=32]

00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI])
        Subsystem: Dell Optiplex GX260
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 17
        Region 4: I/O ports at ff60 [size=32]

00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI])
        Subsystem: Dell Optiplex GX260
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 18
        Region 4: I/O ports at ff40 [size=32]

00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI])
        Subsystem: Dell Optiplex GX260
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 19
        Region 0: Memory at ffa00800 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+
        Capabilities: [58] Debug port

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 81) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: ff800000-ff9fffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 01)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 01) (prog-if 8a [Master SecP PriP])
        Subsystem: Dell Optiplex GX260
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4 [size=1]
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374 [size=1]
        Region 4: I/O ports at ffa0 [size=16]
        Region 5: Memory at 10000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01)
        Subsystem: Dell Optiplex GX260
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin B routed to IRQ 11
        Region 4: I/O ports at dc80 [size=32]

00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
        Subsystem: Dell Unknown device 0126
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 20
        Region 0: I/O ports at d800 [size=256]
        Region 1: I/O ports at dc40 [size=64]
        Region 2: Memory at ffa00400 (32-bit, non-prefetchable) [size=512]
        Region 3: Memory at ffa00000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:0c.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)
        Subsystem: Dell Optiplex GX260
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (63750ns min), Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at ff8e0000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at ecc0 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] PCI-X non-bridge device
                Command: DPERE- ERO+ RBC=512 OST=1
                Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
        Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000 Data: 0000

This is my # lspci -vvn

00:00.0 0600: 8086:2560 (rev 01)
        Subsystem: 1028:0126
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
        Latency: 0
        Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [e4] Vendor Specific Information

00:02.0 0300: 8086:2562 (rev 01) (prog-if 00 [VGA])
        Subsystem: 1028:0126
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
        Region 1: Memory at ff680000 (32-bit, non-prefetchable) [size=512K]
        Capabilities: [d0] Power Management version 1
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 0c03: 8086:24c2 (rev 01) (prog-if 00 [UHCI])
        Subsystem: 1028:0126
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 16
        Region 4: I/O ports at ff80 [size=32]

00:1d.1 0c03: 8086:24c4 (rev 01) (prog-if 00 [UHCI])
        Subsystem: 1028:0126
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 17
        Region 4: I/O ports at ff60 [size=32]

00:1d.2 0c03: 8086:24c7 (rev 01) (prog-if 00 [UHCI])
        Subsystem: 1028:0126
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin C routed to IRQ 18
        Region 4: I/O ports at ff40 [size=32]

00:1d.7 0c03: 8086:24cd (rev 01) (prog-if 20 [EHCI])
        Subsystem: 1028:0126
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin D routed to IRQ 19
        Region 0: Memory at ffa00800 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME+
        Capabilities: [58] Debug port

00:1e.0 0604: 8086:244e (rev 81) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
        Latency: 0
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: ff800000-ff9fffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 0601: 8086:24c0 (rev 01)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0

00:1f.1 0101: 8086:24cb (rev 01) (prog-if 8a [Master SecP PriP])
        Subsystem: 1028:0126
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin A routed to IRQ 18
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4 [size=1]
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374 [size=1]
        Region 4: I/O ports at ffa0 [size=16]
        Region 5: Memory at 10000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 0c05: 8086:24c3 (rev 01)
        Subsystem: 1028:0126
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Interrupt: pin B routed to IRQ 11
        Region 4: I/O ports at dc80 [size=32]

00:1f.5 0401: 8086:24c5 (rev 01)
        Subsystem: 1028:0126
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 0
        Interrupt: pin B routed to IRQ 20
        Region 0: I/O ports at d800 [size=256]
        Region 1: I/O ports at dc40 [size=64]
        Region 2: Memory at ffa00400 (32-bit, non-prefetchable) [size=512]
        Region 3: Memory at ffa00000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:0c.0 0200: 8086:100e (rev 02)
        Subsystem: 1028:002e
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 64 (63750ns min), Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 18
        Region 0: Memory at ff8e0000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at ecc0 [size=64]
        Capabilities: [dc] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [e4] PCI-X non-bridge device
                Command: DPERE- ERO+ RBC=512 OST=1
                Status: Dev=00:00.0 64bit- 133MHz- SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
        Capabilities: [f0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
                Address: 0000000000000000 Data: 0000

After the grub options, the screen goes blank and the first thing which shows up (after a while for the actual boot time) is the log on prompt for the session (gdm).

Every other graphical (GUI) aspect of the Feisty seems OK after the log on (so far).

I am using a Philips 105s monitor with the desktop.

The text mode under TTY terminals are also corrupted (CTRL+ALT+F1 ... F6), because the text shows up very large on the screen (some 4 times the usual size) and it scrools all the way to a line "outside" the visible portion turning the option unusable.

The gnome-terminal works fine under the GUI both for bask and zsh.

The installation process went rather smoothly.

Revision history for this message
PresuntoRJ (fabio-tleitao) wrote :

This is the hardware ID according to the Ubuntu Device Database: e7fd27a8514ed7a2bf02b40b6795bdbf

Revision history for this message
PresuntoRJ (fabio-tleitao) wrote :

$ cat /proc/version
Linux version 2.6.20-14-generic (root@rothera) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Mon Apr 2 20:37:49 UTC 2007

Revision history for this message
PresuntoRJ (fabio-tleitao) wrote :

$ cat /proc/version
Linux version 2.6.20-14-generic (root@rothera) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Mon Apr 2 20:37:49 UTC 2007

Revision history for this message
PresuntoRJ (fabio-tleitao) wrote :
Revision history for this message
ClemensLF (xeno-clf) wrote :

I had the same problem and, luckily, discovered a way to fix it.

1. I updated the BIOS to Rev A09 (I was using A06)
    I am not sure if this is necessary, but I've done it prior to discovering the solution.

2. In the BIOS setup in the menu "Intergrated Devices (LegacySelect Options)" I increased "Onboard Video Buffer" from 1 MB to 8 MB.

That's it, as far as my setup was concerned. I hope this is general solution.

Revision history for this message
PresuntoRJ (fabio-tleitao) wrote : Re: [Bug 105672] Re: usplash and TTY terminals wont show up with Feisty on my Dell GX 260 Intel 82845G video chipset

Well,

I already had the A09 version, so it could not be this.

But I also had the video buffer on 1MB.

Changing it to 8MB solved the problem.

That is good, no doubt, but I have no idea why it was causing this issue or
what happened here.

I have other Dells (not the same model) and this never happened to any of
them.

Thanx for the solution.

On 4/24/07, ClemensLF <email address hidden> wrote:
>
> I had the same problem and, luckily, discovered a way to fix it.
>
> 1. I updated the BIOS to Rev A09 (I was using A06)
> I am not sure if this is necessary, but I've done it prior to
> discovering the solution.
>
> 2. In the BIOS setup in the menu "Intergrated Devices (LegacySelect
> Options)" I increased "Onboard Video Buffer" from 1 MB to 8 MB.
>
> That's it, as far as my setup was concerned. I hope this is general
> solution.
>
> --
> usplash and TTY terminals wont show up with Feisty on my Dell GX 260
> Intel 82845G video chipset
> https://bugs.launchpad.net/bugs/105672
> You received this bug notification because you are a direct subscriber
> of the bug.
>

--

Fábio Leitão, RCDD

Revision history for this message
Saivann Carignan (oxmosys) wrote :

Thanks for your bug report and for your contribution to ubuntu. This bug is a duplicate of bug 68012 so I mark it as such but I will forward your great workaround in that bug. Any further discussions about that bug should take place in the other bug report. Thanks a lot for finding this out.

Revision history for this message
PresuntoRJ (fabio-tleitao) wrote : Invitation to connect on LinkedIn

LinkedIn
------------

Bug,

I'd like to add you to my professional network on LinkedIn.

- Fabio

Learn more:
https://www.linkedin.com/e/isd/411796697/Y0SFIw4i/

------------------------------------------

What is LinkedIn and why should you join?
http://learn.linkedin.com/what-is-linkedin/

------
(c) 2008, LinkedIn Corporation

To post a comment you must log in.
This report contains Public information  
Everyone can see this information.
Subscribing...

Other bug subscribers

Remote bug watches

Bug watches keep track of this bug in other bug trackers.