beagle kernel panic on oneiric omap3-x11 hwpack

beagle board

hwpack is omap3-x11 dated from 1014 2011

panic on boot up

Running bootscript from mmc ...
## Executing script at 82000000
reading uImage

3953816 bytes read
reading uInitrd

1865154 bytes read
reading board.dtb

316 bytes read
## Booting kernel from Legacy Image at 80000000 ...
   Image Name: Linux
   Image Type: ARM Linux Kernel Image (uncompressed)
   Data Size: 3953752 Bytes = 3.8 MiB
   Load Address: 80008000
   Entry Point: 80008000
   Verifying Checksum ... OK
## Loading init Ramdisk from Legacy Image at 81600000 ...
   Image Name: initramfs
   Image Type: ARM Linux RAMDisk Image (uncompressed)
   Data Size: 1865090 Bytes = 1.8 MiB
   Load Address: 00000000
   Entry Point: 00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 815f0000
   Booting using the fdt blob at 0x815f0000
   Loading Kernel Image ... OK
OK
   Using Device Tree in place at 815f0000, end 815f313b

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Linux version 3.0.0-1007-linaro-omap (buildd@chort) (gcc version)
[ 0.000000] CPU: ARMv7 Processor [411fc083] revision 3 (ARMv7), cr=50c5387f
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction ce
[ 0.000000] Machine: OMAP3 Beagle Board, model: TI OMAP3 BeagleBoard
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Reserving 12582912 bytes SDRAM for VRAM
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] OMAP3430/3530 ES3.1 (l2cache iva sgx neon isp )
[ 0.000000] SRAM: Mapped pa 0x40200000 to va 0xfe400000 size: 0x10000
[ 0.000000] Clocking rate (Crystal/Core/MPU): 26.0/332/500 MHz
[ 0.000000] Reprogramming SDRC clock to 332000000 Hz
[ 0.000000] PERCPU: Embedded 7 pages/cpu @80e4c000 s7168 r8192 d13312 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pa2
[ 0.000000] Kernel command line: console=tty0 console=ttyO2,115200n8 root=UU0
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] Memory: 244MB = 244MB total
[ 0.000000] Memory: 233144k/233144k available, 29000k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
[ 0.000000] vmalloc : 0x90800000 - 0xf8000000 (1656 MB)
[ 0.000000] lowmem : 0x80000000 - 0x90000000 ( 256 MB)
[ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
[ 0.000000] modules : 0x7f800000 - 0x7fe00000 ( 6 MB)
[ 0.000000] .text : 0x80008000 - 0x805f2c28 (6060 kB)
[ 0.000000] .init : 0x805f3000 - 0x80646c00 ( 335 kB)
[ 0.000000] .data : 0x80648000 - 0x806ccc70 ( 532 kB)
[ 0.000000] .bss : 0x806ccc94 - 0x80c45118 (5602 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:410
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 4.0) with 96 interrups
[ 0.000000] Total of 96 interrupts on 1 active controller
[ 0.000000] omap_hwmod: gpt12_fck: missing clockdomain for gpt12_fck.
[ 0.000000] OMAP clockevent source: GPTIMER12 at 32768 Hz
[ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 1s
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] console [tty0] enabled
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingr
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3695 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.067687] Calibrating delay loop... 515.72 BogoMIPS (lpj=2015232)
[ 0.108734] pid_max: default: 32768 minimum: 301
[ 0.114776] Security Framework initialized
[ 0.119323] AppArmor: AppArmor initialized
[ 0.123748] Yama: becoming mindful.
[ 0.128143] Mount-cache hash table entries: 512
[ 0.141571] CPU: Testing write buffer coherency: ok
[ 0.147338] ftrace: allocating 24048 entries in 48 pages
[ 0.255432] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.260986] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 countee
[ 0.318450] Brought up 1 CPUs
[ 0.321655] SMP: Total of 1 processors activated (515.72 BogoMIPS).
[ 0.331848] devtmpfs: initialized
[ 0.354766] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_core
[ 0.362396] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_per
[ 0.369934] omap_hwmod: _populate_mpu_rt_base found no _mpu_rt_va for l4_wkup
[ 0.394683] omap_hwmod: i2c1: softreset failed (waited 10000 usec)
[ 0.416320] omap_hwmod: i2c2: softreset failed (waited 10000 usec)
[ 0.438018] omap_hwmod: i2c3: softreset failed (waited 10000 usec)
[ 0.445404] omap_hwmod: am35x_otg_hs: cannot be enabled (3)
[ 0.459075] print_constraints: dummy:
[ 0.465209] NET: Registered protocol family 16
[ 0.471496] GPMC revision 5.0
[ 0.487365] omap_device: omap_gpio.0: new worst case activate latency 0: 1220
[ 0.499420] OMAP GPIO hardware version 2.5
[ 0.506164] OMAP GPIO hardware version 2.5
[ 0.512359] OMAP GPIO hardware version 2.5
[ 0.518890] OMAP GPIO hardware version 2.5
[ 0.525360] OMAP GPIO hardware version 2.5
[ 0.531799] OMAP GPIO hardware version 2.5
[ 0.548706] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.558654] OMAP3 Beagle Rev: C4
[ 0.574249] omap_device: omap_uart.0: new worst case activate latency 0: 3057
[ 0.586700] omap_device: omap_uart.2: new worst case deactivate latency 0: 37
[ 0.598327] Found NAND on CS0
[ 0.601501] Registering NAND on CS0
[ 0.606781] Unable to get DVI reset GPIO
[ 0.627838] No ATAGs?
[ 0.630035] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.741668] Switched to new clocking rate (Crystal/Core/MPU): 26.0/332/720 Mz
[ 0.750671] OMAP DMA hardware revision 4.0
[ 0.756561] Serial: AMBA PL011 UART driver
[ 0.849426] bio: create slab <bio-0> at 0
[ 0.863098] SCSI subsystem initialized
[ 0.870025] omap_device: omap2_mcspi.1: new worst case activate latency 0: 37
[ 0.880035] omap_device: omap2_mcspi.1: new worst case deactivate latency 0:7
[ 0.895294] usbcore: registered new interface driver usbfs
[ 0.902435] usbcore: registered new interface driver hub
[ 0.909271] usbcore: registered new device driver usb
[ 0.918640] omap_device: omap_i2c.1: new worst case activate latency 0: 30517
[ 0.926574] omap_i2c omap_i2c.1: bus 1 rev3.12 at 2600 kHz
[ 0.943664] twl4030: PIH (irq 7) chaining IRQs 368..375
[ 0.949615] twl4030: power (irq 373) chaining IRQs 376..383
[ 0.957519] twl4030: gpio (irq 368) chaining IRQs 384..401
[ 0.972229] print_constraints: VUSB1V5: 1500 mV normal standby
[ 0.981231] print_constraints: VUSB1V8: 1800 mV normal standby
[ 0.989807] print_constraints: VUSB3V1: 3100 mV normal standby
[ 1.002105] twl4030_usb twl4030_usb: Initialized TWL4030 USB module
[ 1.014068] print_constraints: VMMC1: 1850 <--> 3150 mV at 3000 mV normal sty
[ 1.024444] print_constraints: VDAC: 1800 mV normal standby
[ 1.033325] print_constraints: VPLL2: 1800 mV normal standby
[ 1.041961] print_constraints: VSIM: 1800 <--> 3000 mV at 1800 mV normal stay
[ 1.050659] omap_device: omap_i2c.1: new worst case deactivate latency 0: 307
[ 1.067901] omap_i2c omap_i2c.3: bus 3 rev3.12 at 100 kHz
[ 1.084411] NetLabel: Initializing
[ 1.088043] NetLabel: domain hash size = 128
[ 1.093109] NetLabel: protocols = UNLABELED CIPSOv4
[ 1.098663] NetLabel: unlabeled traffic allowed by default
[ 1.104675] Switching to clocksource 32k_counter
[ 1.116851] Switched to NOHz mode on CPU #0
[ 1.183807] AppArmor: AppArmor Filesystem Enabled
[ 1.265014] NET: Registered protocol family 2
[ 1.270812] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 1.280151] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.288085] TCP bind hash table entries: 8192 (order: 6, 327680 bytes)
[ 1.298736] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.305511] TCP reno registered
[ 1.308929] UDP hash table entries: 128 (order: 1, 12288 bytes)
[ 1.315460] UDP-Lite hash table entries: 128 (order: 1, 12288 bytes)
[ 1.323242] NET: Registered protocol family 1
[ 1.329559] RPC: Registered named UNIX socket transport module.
[ 1.335815] RPC: Registered udp transport module.
[ 1.341094] RPC: Registered tcp transport module.
[ 1.346130] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.354614] Trying to unpack rootfs image as initramfs...
[ 1.560699] Freeing initrd memory: 1820K
[ 1.571136] PMU: registered new PMU device of type 0
[ 1.581207] audit: initializing netlink socket (disabled)
[ 1.587554] type=2000 audit(1.460:1): initialized
[ 1.739685] Kprobe smoke test started
[ 1.752960] Kprobe smoke test failed: register_jprobe returned -22
[ 1.759552] Kprobe smoke test failed: register_jprobes returned -22
[ 1.774688] BUG: Kprobe smoke test: 2 out of 6 tests failed
[ 1.798339] JFFS2 version 2.2. (NAND) (SUMMARY) �© 2001-2006 Red Hat, Inc.
[ 1.808898] Btrfs loaded
[ 1.811676] msgmni has been set to 458
[ 1.820831] Block layer SCSI generic (bsg) driver version 0.4 loaded (major )
[ 1.829162] io scheduler noop registered
[ 1.833312] io scheduler deadline registered
[ 1.838073] io scheduler cfq registered (default)
[ 1.907806] OMAP DSS rev 2.0
[ 1.922515] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.994537] omap_uart.0: ttyO0 at MMIO 0x4806a000 (irq = 72) is a OMAP UART0
[ 2.016937] omap_uart.1: ttyO1 at MMIO 0x4806c000 (irq = 73) is a OMAP UART1
[ 2.040374] omap_uart.2: ttyO2 at MMIO 0x49020000 (irq = 74) is a OMAP UART2
[ 2.048004] console [ttyO2] enabled, bootconsole disabled
[ 2.048004] console [ttyO2] enabled, bootconsole disabled
[ 2.073089] [drm] Initialized drm 1.1.0 20060810
[ 2.115783] brd: module loaded
[ 2.138336] loop: module loaded
[ 2.142578] omap_device: omap_i2c.1: new worst case activate latency 0: 91552
[ 2.158172] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.165893] omap2-nand driver initializing
[ 2.170776] ONFI flash detected
[ 2.174407] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xba (Micron NAND 2)
[ 2.183654] Creating 5 MTD partitions on "omap2-nand.0":
[ 2.189331] 0x000000000000-0x000000080000 : "X-Loader"
[ 2.203857] 0x000000080000-0x000000260000 : "U-Boot"
[ 2.216125] 0x000000260000-0x000000280000 : "U-Boot Env"
[ 2.227203] 0x000000280000-0x000000680000 : "Kernel"
[ 2.240051] 0x000000680000-0x000010000000 : "File System"
[ 2.370391] OneNAND driver initializing
[ 2.383453] usbcore: registered new interface driver asix
[ 2.390014] usbcore: registered new interface driver cdc_ether
[ 2.397216] usbcore: registered new interface driver smsc95xx
[ 2.404022] usbcore: registered new interface driver net1080
[ 2.410736] usbcore: registered new interface driver cdc_subset
[ 2.417663] usbcore: registered new interface driver zaurus
[ 2.423767] cdc_ncm: 01-June-2011
[ 2.427764] usbcore: registered new interface driver cdc_ncm
[ 2.435913] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.454284] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 4.463684] ehci-omap ehci-omap.0: new USB bus registered, assigned bus numb1
[ 4.472259] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 4.493438] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 4.500671] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.507873] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber1
[ 4.515533] usb usb1: Product: OMAP-EHCI Host Controller
[ 4.521148] usb usb1: Manufacturer: Linux 3.0.0-1007-linaro-omap ehci_hcd
[ 4.528320] usb usb1: SerialNumber: ehci-omap.0
[ 4.539306] hub 1-0:1.0: USB hub found
[ 4.543701] hub 1-0:1.0: 3 ports detected
[ 4.579833] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.586730] ohci-omap3 ohci-omap3.0: OMAP3 OHCI Host Controller
[ 4.594726] ohci-omap3 ohci-omap3.0: new USB bus registered, assigned bus nu2
[ 4.603302] ohci-omap3 ohci-omap3.0: irq 76, io mem 0x48064400
[ 4.686920] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 4.694122] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber1
[ 4.701751] usb usb2: Product: OMAP3 OHCI Host Controller
[ 4.707489] usb usb2: Manufacturer: Linux 3.0.0-1007-linaro-omap ohci_hcd
[ 4.714660] usb usb2: SerialNumber: ohci-omap3.0
[ 4.722686] hub 2-0:1.0: USB hub found
[ 4.726684] hub 2-0:1.0: 3 ports detected
[ 4.734466] usbcore: registered new interface driver cdc_wdm
[ 4.740661] Initializing USB Mass Storage driver...
[ 4.746612] usbcore: registered new interface driver usb-storage
[ 4.754180] USB Mass Storage support registered.
[ 4.760864] usbcore: registered new interface driver libusual
[ 4.877685] usb 1-2: new high speed USB device number 2 using ehci-omap
[ 5.040954] usb 1-2: New USB device found, idVendor=0409, idProduct=005a
[ 5.048065] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.059417] hub 1-2:1.0: USB hub found
[ 5.063934] hub 1-2:1.0: 4 ports detected
[ 5.073059] usbcore: registered new interface driver usbtest
[ 5.084655] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 5.099914] input: twl4030_pwrbutton as /devices/platform/omap/omap_i2c.1/i21
[ 5.118988] twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0
[ 5.128479] i2c /dev entries driver
[ 5.137207] Driver for 1-wire Dallas network protocol.
[ 5.144989] omap_device: omap_wdt.-1: new worst case activate latency 0: 3057
[ 5.154724] OMAP Watchdog Timer Rev 0x31: initial timeout 60 sec
[ 5.162475] twl4030_wdt twl4030_wdt: Failed to register misc device
[ 5.170135] twl4030_wdt: probe of twl4030_wdt failed with error -16
[ 5.180755] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-m
[ 5.332885] usbcore: registered new interface driver usbhid
[ 5.339324] usbhid: USB HID core driver
[ 5.345581] oprofile: using arm/armv7
[ 5.350341] TCP cubic registered
[ 5.354095] Initializing XFRM netlink socket
[ 5.359405] NET: Registered protocol family 10
[ 5.364746] usb 1-2.3: new high speed USB device number 3 using ehci-omap
[ 5.375061] IPv6 over IPv4 tunneling driver
[ 5.383514] NET: Registered protocol family 17
[ 5.388824] NET: Registered protocol family 15
[ 5.394134] Registering the dns_resolver key type
[ 5.400207] VFP support v0.3: implementor 41 architecture 3 part 30 variant 1
[ 5.408477] ThumbEE CPU extension supported.
[ 5.412994] Registering SWP/SWPB emulation handler
[ 5.428863] omap2_set_init_voltage: unable to find boot up OPP for vdd_mpu
[ 5.436187] omap2_set_init_voltage: Unable to put vdd_mpu to its init voltage
[ 5.436187]
[ 5.491088] clock: disabling unused clocks to save power
[ 5.503082] fbcvt: 1280x720@60: CVT Name - .921M9-R
[ 5.511230] usb 1-2.3: New USB device found, idVendor=05ac, idProduct=1005
[ 5.518615] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumbe3
[ 5.529785] usb 1-2.3: Product: Keyboard Hub
[ 5.548248] usb 1-2.3: Manufacturer: Apple Inc.
[ 5.548278] usb 1-2.3: SerialNumber: 000000000000
[ 5.551422] hub 1-2.3:1.0: USB hub found
[ 5.551666] hub 1-2.3:1.0: 3 ports detected
[ 5.555389] Console: switching to colour frame buffer device 160x45
[ 5.600494] regulator_init_complete: VDAC: incomplete constraints, leaving on
[ 5.610137] twl_rtc twl_rtc: setting system clock to 2011-10-14 19:02:42 UTC)
[ 5.623687] Freeing init memory: 332K
[ 5.650115] usb 1-2.4: new high speed USB device number 4 using ehci-omap
[ 5.681091] mmc0: new SDHC card at address aaaa
[ 5.705749] mmcblk0: mmc0:aaaa SU04G 3.69 GiB
[ 5.735260] mmcblk0: p1 p2
Loading, please wait...
[ 5.797302] usb 1-2.4: New USB device found, idVendor=0b95, idProduct=772a
[ 5.820098] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumbe3
[ 5.845031] usb 1-2.4: Product: AX88x72A
[ 5.861389] usb 1-2.4: Manufacturer: ASIX Elec. Corp.
[ 5.884277] usb 1-2.4: SerialNumber: 4A7178
[ 5.998779] udevd[690]: starting version 173
Begin: Loading essential drivers ... done.
[ 6.854461] asix 1-2.4:1.0: eth0: register 'asix' at usb-ehci-omap.0-2.4, AS8
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
[ 7.204833] usb 1-2.3.2: new low speed USB device number 5 using ehci-omap
Begin: Running /scripts/local-premount ... [ 7.360443] usb 1-2.3.2: New USB d
[ 7.424896] usb 1-2.3.2: New USB device strings: Mfr=1, Product=2, SerialNum0
[ 7.532470] usb 1-2.3.2: Product: Apple Keyboard
[ 7.703674] usb 1-2.3.2: Manufacturer: Apple Inc.
[ 7.853576] input: Apple Inc. Apple Keyboard as /devices/platform/usbhs-omap2
[ 8.019104] apple 0003:05AC:021D.0001: input: USB HID v1.11 Keyboard [Apple 0
done.
[ 8.202178] input: Apple Inc. Apple Keyboard as /devices/platform/usbhs-omap3
[ 8.324951] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. )
[ 8.356689] apple 0003:05AC:021D.0002: input: USB HID v1.11 Device [Apple In1
Begin: Running /scripts/local-bottom ... done.
done.
Begin: Running /scripts/init-bottom ... [ 8.626739] usb 1-2.3.3: new low spep
[ 8.814025] usb 1-2.3.3: New USB device found, idVendor=046d, idProduct=c00e
[ 8.832153] usb 1-2.3.3: New USB device strings: Mfr=1, Product=2, SerialNum0
done.
[ 8.850830] usb 1-2.3.3: Product: USB-PS/2 Optical Mouse
[ 8.860992] usb 1-2.3.3: Manufacturer: Logitech
[ 8.880249] input: Logitech USB-PS/2 Optical Mouse as /devices/platform/usbh4
[ 8.901275] generic-usb 0003:046D:C00E.0003: input: USB HID v1.10 Mouse [Log0
[ 13.689239] init: Caught segmentation fault, core dumped
[ 13.799713] Kernel panic - not syncing: Attempted to kill init!
[ 13.810913] [<800110ad>] (unwind_backtrace+0x1/0x90) from [<803e0b81>] (pani)
[ 13.824310] [<803e0b81>] (panic+0x45/0x120) from [<800388b3>] (forget_origin)
[ 13.838409] [<800388b3>] (forget_original_parent+0x67/0x14c) from [<800389a9)
[ 13.853027] [<800389a9>] (exit_notify+0x11/0xd4) from [<80038e67>] (do_exit+)
[ 13.866394] [<80038e67>] (do_exit+0x21b/0x28c) from [<80039045>] (do_group_e)
[ 13.880279] [<80039045>] (do_group_exit+0x65/0x84) from [<80039075>] (sys_ex)
[ 13.894439] [<80039075>] (sys_exit_group+0x11/0x14) from [<8000c2c1>] (ret_f)